External Design (cont’d)
Taking a look at the SilverStone case from other angles, we find again that the case is much simpler than the X-QPack, and certainly as sleek as most Shuttles.
Click to enlarge.
Click to enlarge.
Venting holes along the entire bottom of both sides provide the exhaust fans with enough cool intake air to keep the entire system cool. This is quite a bit different from the X-QPack, which only allowed air to come in at the front of the case. It will be interesting to see how this affects the cooling performance between the two cases.
Click to enlarge.
Instead of showing an empty case as we normally do, we decided to give our readers a better idea of what a completed system might look like by showing a shot of the back with our test bed installed. Like the X-QPack, the cover of the SG01 is a single piece, and is secured to the rest of the chassis with four screws (one of which has been removed in this picture). However, right away, we also notice that the cases take a very different approach to the layout of the back, as the SG01 places the power supply to the far left and a much smaller 60mm fan located above the expansion cards.
Facebook
Twitter
RSS
18 Comments
View All Comments
Tamale - Wednesday, October 26, 2005 - link
exactly!cryptonomicon - Wednesday, October 26, 2005 - link
reminds me of lian-lisegagenesis - Wednesday, October 26, 2005 - link
But the final words say it all. Despite the nifty ideas like the hard drive cage with a fan (hard drives burning up would worry me most in a HTPC) and the ability to use a normal sized power supply... the noise would kill this off my list instantly. A noisy computer is one thing, but the whine from smaller fans really aggrivate me. I'll give them the fact its probably exceedingly difficult to put 120mm fans in a HTPC case, but I'll be damned if the thing is louder than my TT Armour.imaheadcase - Wednesday, October 26, 2005 - link
Its a good thing actully that it uses a real power supply. The fail rate on Shuttle SFF power supply is VERY high, i currently have mine hooked up to a regular power supply (case cover off of course) because power supply failed.Just get a new PS you say? The cheapest one is about $60. a hundred more you can get a NEW SFF case/PS/Mobo. Its a vicious cycle. :(
Im just going to transfer CPU/RAM/Video card to a midtower case and be done with it.
just1ed - Sunday, November 11, 2007 - link
Hi imaheadcase,I'm interested to know how you modded a normal ATX to Shuttle's XPC PSU. They have some non standard heads. My XPC's PSU blew and I'm not interested in replacing it with another expensive PSU that might die in the near future.
BigSky - Friday, September 15, 2006 - link
I can't run a video card in my SS51G that requires an external power source. The wimpy 200W Shuttle PS can't do the job. I'm too cheap to spring for a new PS but have plenty of ATX PSs laying around and was thinking of doing what you did to power the Shuttle with an ATX PS. I see that the motherboard uses a 4 pin connector like the standard one for a peripheral vice the square 4 pin cable on most motherboards. Should I make an adapter from the ATX PS's square 4 pin to connector to the Shuttle MB 4 pin connector vice using one of the peripheral power leads? Seems this would be better from a power mgmt perspective. I don't understand if this ATX power lead is independent of the peripheral leads.bmartin1984@verizon.net
Thanks.
ProphetCHRIS - Wednesday, October 26, 2005 - link
The problem of the manufacturers is just that they have to built these cases for "average" people. You can surely put own low-noise fans inside and it wont go off in flames. I have built once this kind of case with an old Lian Li. I put dampening material inside and only one fan. Sure it was a little warmer than normal cases but I operated it 24/7 for two years.I am sure this case has much potential with just a little help...
Tamale - Wednesday, October 26, 2005 - link
aye.. but should a $150 case need any help? ;)