Scythe Ninja Plus Rev. B: Updated Cooling Legend
by Wesley Fink on April 11, 2007 2:00 AM EST- Posted in
- Cases/Cooling/PSUs
Cooling at Stock Speed
Some users will never overclock their CPU, but they still want to run the coolest CPU temperatures possible to enhance stability and extend CPU life. The Scythe Ninja Plus B kit includes a moderate output low noise 120mm fan. We also tested the Vindicator with the 120mm SilenX IXTREMA 120 fan.
With the stock fan the end user does get relative silence, but the cost is poorer cooling than most other heatpipe towers tested at AnandTech. As soon as the switch is made to the SilenX fan you can see this cooler is starved for airflow with the stock fan. Idle temps with the SilenX drop to 27C, which is among the best measured performance at stock Idle in our cooler reviews
It is more difficult to effectively simulate a computer being stressed by all of the conditions it might be exposed to in different operating environments. For most home users CPU power is most taxed with contemporary gaming. Therefore our stress test simulates running a demanding contemporary game.
The Far Cry River demo is looped for 30 minutes and the CPU temperature is captured at 4 second intervals with the NVIDIA monitor "logging" option. The highest temperature during the stress test is then reported. Momentary spikes are ignored, as we report a sustained high-level temp that you would expect to find in this recording configuration.
Cooling efficiency of the Scythe Ninja Plus B was tested under load conditions with both the stock fan and the SilenX at stock speed. Results are compared to the Intel retail HSF and other recently tested CPU coolers.
The Ninja Plus B under load at stock speeds reached a maximum temperature of 47C with the stock cooler. This was among the worst load results at stock speed with the coolers tested at AnandTech. Switching to the SilenX fan improved the load temperature to 35C. This is a stellar result, and one of the best stock speed load temperatures we have tested. This compared to the Tuniq at 34C, the Cooler Master Hyper 6+ and Zalman 9700 at 36C, the Thermalright Ultra 120 at 33C , and the top Ultra 120 Extreme at 32C.
It should also be clear that cooling results with the Scythe Ninja Plus B are quite different than results with the OCZ Vindicator using the same SilenX fan. The Ninja Plus B cools better than the Vindicator using the same fan. This strongly suggests that while the Vindicator looks similar it is not just a rebadged Scythe Ninja Rev. B. There are enough differences in their designs to have an impact on cooling performance. This becomes clearer in a closer look at cooler performance scaling.
Some users will never overclock their CPU, but they still want to run the coolest CPU temperatures possible to enhance stability and extend CPU life. The Scythe Ninja Plus B kit includes a moderate output low noise 120mm fan. We also tested the Vindicator with the 120mm SilenX IXTREMA 120 fan.
With the stock fan the end user does get relative silence, but the cost is poorer cooling than most other heatpipe towers tested at AnandTech. As soon as the switch is made to the SilenX fan you can see this cooler is starved for airflow with the stock fan. Idle temps with the SilenX drop to 27C, which is among the best measured performance at stock Idle in our cooler reviews
It is more difficult to effectively simulate a computer being stressed by all of the conditions it might be exposed to in different operating environments. For most home users CPU power is most taxed with contemporary gaming. Therefore our stress test simulates running a demanding contemporary game.
The Far Cry River demo is looped for 30 minutes and the CPU temperature is captured at 4 second intervals with the NVIDIA monitor "logging" option. The highest temperature during the stress test is then reported. Momentary spikes are ignored, as we report a sustained high-level temp that you would expect to find in this recording configuration.
Cooling efficiency of the Scythe Ninja Plus B was tested under load conditions with both the stock fan and the SilenX at stock speed. Results are compared to the Intel retail HSF and other recently tested CPU coolers.
The Ninja Plus B under load at stock speeds reached a maximum temperature of 47C with the stock cooler. This was among the worst load results at stock speed with the coolers tested at AnandTech. Switching to the SilenX fan improved the load temperature to 35C. This is a stellar result, and one of the best stock speed load temperatures we have tested. This compared to the Tuniq at 34C, the Cooler Master Hyper 6+ and Zalman 9700 at 36C, the Thermalright Ultra 120 at 33C , and the top Ultra 120 Extreme at 32C.
It should also be clear that cooling results with the Scythe Ninja Plus B are quite different than results with the OCZ Vindicator using the same SilenX fan. The Ninja Plus B cools better than the Vindicator using the same fan. This strongly suggests that while the Vindicator looks similar it is not just a rebadged Scythe Ninja Rev. B. There are enough differences in their designs to have an impact on cooling performance. This becomes clearer in a closer look at cooler performance scaling.
Facebook
Twitter
RSS
36 Comments
View All Comments
Lord Evermore - Saturday, April 14, 2007 - link
How is the Ninja and Infinity "not particularly great for overclocking", when even with their stock fans, when they can hit 3.83GHz? 3.9GHz is only 66MHz higher, a whopping 1.7% higher. Individual CPU differences could easily make that up for other users, and the "better" coolers might not get an equal increase in their maximum speed in those cases. At those levels to me things seem for all intents and purposes essentially equal.With the stock fan that's a 31% overclock at 3.83G. 33% at 3.9G. Only in comparison to the very best you've tested do these come out near the lower end of the scale. Right at the end you group it together with the top tier of other coolers. And even if it was at the lower end of the "good" coolers, stock or overclocked, the actual numerical differences are so tiny as to be statistically insignificant.
I suppose 66MHz difference is a HUGE deal to rabid overclockers who are willing to spend money for it, but the majority of even enthusiasts I'd think wouldn't consider it particularly impressive given how large the stock fan overclock is. (Note I'm only addressing the frequency obtained since that seems to be the focus of what makes a cooler "good" here. Temperatures obtained at those speeds could change the lineup.)
Wesley Fink - Monday, April 16, 2007 - link
We use the exact same CPU and test bed for testing all coolers - to remove the "individual CPU" variable. But you are right to put the performance results into perspective. In the grand scheme of performance the difference in 3.83GHz and 3.90GHz is very small as you point out. There are other advantages to the very top performing coolers, however. If you check the cooling at various temps those that do 3.90GHz easily also generally provide the lowest CPU temperaturesa at any given speed.Had we devised our overclocking test a little differently and tested say, every 266 MHz - 2.93GHz, 3.2GHz, 3.466GHz, 3.633GHz, 3.80GHz, 3.966GHz - the true differences might be put in better perspective. However, we started the test with the assumption that if a cooler couldn't outperform the Intel Retail there was no point in buying it. Perhaps if the Intel Retail HSF were poorer we could show more, but the fact is the Intel Retail HSF is really very good and it takes a decent cooler to beat the one that comes at no additional cost with the Intel processor.
Your comments are fair, but we also believe our cooler test methods do identify the very top performers in the marketplace. One notch down is still pretty remarkable performance as you point out.
strikeback03 - Thursday, April 12, 2007 - link
It is kind of hard to tell in the photos, does one set of 3 heat pipes run above the other set, or are they somehow woven together so they are all approximately the same distance from the CPU? Assuming they are mounted with one set above the other, did you do any testing to see whether cooling is better with the fan mounted on one side or the other (i.e. blowing directly on the upper set of heatpipes or the lower set).Wesley Fink - Friday, April 13, 2007 - link
one group of 3 heatpipes passes through an upper plate and the other three pass through the mounting plate below. As you guessed they do cross over the lower set of heatpipes in the center of the base. We did not test with different orientations relative to the heatpipe level, but it is an interesting question.Wesley Fink - Thursday, April 12, 2007 - link
We have received the following statement from Scythe regarding the similarity of their Ninja Plus B Cooler to the OCZ Vindicator:"Scythe is a stock holder of the factory where we produce our coolers,
and also the factory is a stock holder of the Scythe Taiwan office where
we have a very tight relationship almost as close as a group company.
Within this relationship we are acknowledged and aware of all shipments
done from the factory. But OCZ is not one of them.
With the above said, we are definitely sure that OCZ coolers are manufactured
in another factory. The only components that are common between the two are the
hex caps on the heat pipes, which are supplied outside of our cooler factory.
We also have not approved OCZ's design in any form or shape, nor did we receive
any OEM request. Their products are just a simple copy of Ninja and we are
currently being troubled by this untrue rumor. "
Lord Evermore - Saturday, April 14, 2007 - link
My thought is maybe they use a different working fluid. They're just too similar in design for the hardware to have any performance difference, even if OCZ did just copy the design (if they had though, you'd think Scythe would be suing). I suppose the exact alloy composition for the base plate or other parts could be different, if they actually are made somewhere else, and then the parts just end up looking the same and being assembled in the same shape.Then again, Scythe doesn't say NOBODY gets this design but them...
ceefka - Thursday, April 12, 2007 - link
On the packaging of the Ninja it says: "supports fanless model". Now that of course will be dead silent, but it will require adequate airflow in the form of case fans. What are the temperatures and dBs in that situation?Wesley Fink - Thursday, April 12, 2007 - link
Fanless cooling seems to perform best with a PS with a downward facing exhaust fan and excellent case entry and exhaust cooling. Our test case does not really have these features, but we will definitely be paying more attention to airflow and the PS fans in choosing components for our new test bed. With the current configuration in mind, it seemed unfair to test fanless mode temps with a poor configuration for fanless cooling.We did run a quick 5-minute gaming loop at the X6800 stock speed with a fanless Ninja Plus B and it ran fine. Temps were much higher than fan configurations just as you would expect. We will be doing more in testing fanless claims in the future - once the fans are selected from testing and the new test bed is launched.
We do confess concerns over fanless given the current crop of excellent perfroming tower coolers. It appears fanless just moves the fans from the cooler to the case, but fans are still required. There are many large quiet case fans, but there are also many quiet 120mm fans for coolers these days. Fanless seemed to make more difference when ccoolers used buzzy loud 60mm and 70mm fans. These days the best coolers use heatpipes and 120mm fans and the noise levels are MUCH lower with these coolers than the screaming wonders of the past.
fic2 - Thursday, April 12, 2007 - link
I am curious about the Noise Limit heatsinks: http://www.noiselimit.com/index2.asp?id=16">http://www.noiselimit.com/index2.asp?id=16. Any chance this will be included in a review?Stele - Wednesday, April 11, 2007 - link
I'm not sure if this question has been dealt with before - my apologies if it has.I've always wondered how is it that a certain cooler can produce lower CPU temperatures but yet fail to make it at a higher CPU frequency? The Zalman CNPS9700 is a good example - at 3.83GHz the CPU runs at 40°C, which is lower than many of the others, yet does not make it to the last two CPU frequencies. A Scythe Infinity dual, however, registers 44 at the same frequency and yet makes it at least into 3.90GHz. The anomaly is even more pronounced in the stress test. In all cases the coolers seem to scale similarly, so it's not as if one of them had reached its design limit (compared to, for example, the stock Intel HSF). Has an explanation for this been given or proposed before?
I'm guessing that one factor is the mounting method. It's remarkable that some Socket-775 coolers, despite weighing some 1.5-2x that of the official 450g limit with fan, still use the stock plastic push-pin method. Without a backplate. Makes one wonder sometimes whether the cooler is indeed in good contact with the CPU, and whether after some time the cooler would fall out - or the motherboard flex and crack.